Using Silicon Injection Port in Growing Mushrooms

Using Silicon Injection Port in Growing Mushrooms

When you grow magic mushrooms in your own home, contaminants are definitely a threat any grower need to look out for. If you are not cautious, a stray microorganism can ruin an entire grow leading to a great decrease in investment. With the help of air exchange and silicone port for your growing bag or jar, you’ll be able to safeguard your growing mushrooms on the risks of contamination.

There is nothing much more frustrating than finding all of your effort and resources be wasted due to a lapse in sterility. Mushroom growers that are first-timers are also informed about this sense of loss. Although you may have the methods to produce a sterile workplace using sterilized products, things may still go downhill if you are not that careful.

A good way to keep up sterility is through an inoculation jar that has a modified and special lid. This lid enables growers to help keep contaminants from the growing medium that is contained in the inoculation jars.

How can a silicone injection port help?

Holding off the mycelium to the substrate is among the most vulnerable phase within the entire process. Using a silicone injection port helps to ensure those surroundings in which the mycelium takes hold stay free from any microorganisms that could compromise and contaminate the growing procedure. Using an air exchange method enables the mycelium jars to properly breathe.

How to Create a Silicone Injection Port

In creating a customized silicone injection port, you will need to change the jar lids. To create the silicone port, you will require these supplies:

  • Drill that has 6.5mm drill bit
  • Lid which may come from a glass jar
  • RTV silicone sealant
  • Paper

Stick to these easy steps:

  1. Thoroughly clean your lid and jar using a gentle anti-bacterial cleaning soap to lessen its microbe count. This will still need to go through sterilization before using it later on within the growing process.
  2. Drill a few holes in the jar lid. One of the center and the other one on the side. One of these holes will be for the injection port while the other one is for the air exchange port.
  3. Cut into square bits of paper that are big enough to cover these holes.
  4. Select which hole will be the injection port.
  5. As soon as you have decided, grab the silicone sealant and make an outline to the top and under the selected hole.
  6. When you have built the outline, fill out the other circle to the top while using sealant. The bits of paper covering these holes must avoid the silicone from falling to the opposite side. The outline will help hold it all up.
  7. Do the same method again to the other side of the lid.
  8. Use the rest of the paper squares and put them on every side of the silicone. Press both sides down with only enough force so it can be flattened.
  9. Established the lid apart allowing the silicone dry to be intact. Ensure the silicone is not holding anything apart from the paper. It could go through the surface while drying.
  10. As soon as it is dried out, remove the paper layers properly. You’re going to end up having a flat, nice silicone injection port. The port should seal off by itself after use and only the syringe will be left

How to Create an Air Filter Port

When your lids have gotten a secure port by which the spores will be injected, it is now time to create a very simple air exchange port. Air is packed with pollutants and moisture. The concept behind this air exchange port would be to eliminate impurities in the air before they move to the jars. This allows the air to be able to breathe without having to contaminate the mycelium.

With this method, you’ll need these supplies:

  • Aquarium fiber with a cotton filter 
  • Jar with a hole
  • Pliers

Follow these guidelines:

  1. The lid must have the 2nd hole drilled in it after you created the silicone port. The 2nd hole will be the air exchange port.
  2. Get a strip from the aquarium fiber and move it up in order to fill the hole completely.
  3. Fold that into two and the top should be covered with more material. It will make an uncompromised, smooth layer which you can use
  4. Cut down the materials that are still left in your roll. Coming from lid at the bottom, work the centerfold that is covered through up so it pokes to 1cm through the top. This can be tricky but you may use pliers in order to pull it. Ensure that it is tight properly so the air does not quickly get through it.
  5. All loose materials must be cut down in the bottom. You just finished the air exchange port. The layer should catch particles or dust which could harm and contaminate your growing mycelium.
  6. If the methods look complicated for you, just tape some layers of gauze on the lids 

There you go. You already have a modified lid that has an injection port to be used in sterile inoculations. You also have an air filter that will protect against any pesky toxins that may contaminate your grow. Similar methods can be used to make inoculation bags to have an additional safety measure.

Having no air exchange and sterility are some of the reasons why growing mushrooms become unsuccessful. The world is in a constant battle, so to ensure that your psychedelic mycelium is in complete control over the substrate, you need to get rid of as many competitors as you can.

The easy strategies right here might need you to invest extra effort but preventive steps mean you will not have molds, bugs, or other micro-intruders destroying your psychedelic fungi.

If you have the time, resources, and ability to develop your very own magic mushrooms, you may still build your own set of magic truffles with the use of grow kits. Grow kits are properly filled and packaged with mycelium and can bear magic truffles to your psychedelic pleasure within just a few days.

Leave a Reply

FORGOT PASSWORD ?
Lost your password? Please enter your username or email address. You will receive a link to create a new password via email.
We do not share your personal details with anyone.
×
×

Cart